A little aluminum vs. sterling experiment

Screenshot at 2018-08-07 10:22:40

 

I did a little experiment a couple of days ago in my own facebook   https://www.facebook.com/NiciArt/  and a metalsmithing group I belong to that is also in facebook .

My posting there asked the question ” which is which ? ”  What guitar pick is made of sterling and what is the aluminum . Just by looking at a picture . When I did the math about 76% percent picked the wrong metal – by the way the left guitar pick is aluminum the right is sterling .

Now why do this experiment at all and what did I want to gather with it ? My point was that when you buy online not everything you see that is silver is in fact sterling silver . If the price is too good to be true it most likely is . I have seen websites offer sterling silver rings and other jewelry for the fraction of what it would cost someone to buy from me or any other metalsmith .

When you shop online you cannot feel and smell the metal – aluminum feels very different from sterling as does steel or some other silver looking metals .

Even looking at the little stamp 925 ( mostly inside the jewelry or on the back ) does not guarantee that what you get is in fact the real deal .

So when buying online be careful out there . Again – if the price is too good to be true – it might very well be …. 🙂

 

 

 

 

Flaming guitar pick

Rock and Roll Baby ………….

sterling guitar pick pendant with brass flames

the reason – just because I wanted to and I can

I cut out some equal sized guitar picks

one in 20 gauge sterling and one in 20 gauge brass ( copper or bronze will work too ) I filed the edges round with a number 2 file ( pretty fine )

draw your flames onto the brass pick and start cutting with a jewelry saw and 1/0 saw blades

flux your brass flames and add solder – heat with torch until solder melts

solder both sterling and brass together

after quenching and cleaning start filing with a number 2, 3 or 4 file

see the gap ? gap no good , better start filing

file until the solder seam is smooth

start polishing

I just left the metal raw and satin looking and did not add patina drill a hole

add a jump ring and a chain and start rocking

thanks for looking 🙂

winged guitar pendant in sterling silver

This guitar pendant is a bit more involved and I would categorize it in the more intermediate difficulty.

OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA

As almost always I made this one from sterling silver and I love it if I may say so :)

and here is how to do it . Draw your guitar with 2 wings attached on a piece of paper and glue to your metal – I use 18 gauge sterling silver ( if you go thinner then that your fretboard might bend on you. Draw a second set of smaller wings separately and glue this also to the sterling silver . Cut everything out with your jewelry handsaw . also cut out a heart. I use a 6 inch jewelers saw frame with 1/0 saw blades.

OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA

After cutting out your shapes clean your metal with sand paper to ready it for soldering . Flux the back of your small wings and heart and add your solder- I use hard silver solder in wire form . There are many different kind of solders .I happen to like stick or wire solder the best. Heat with your torch until the solder melts and spreads out. Quench in water

OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA

Flux the front of your guitar with the wings and put the smaller wings and the heart onto it solder site down . Heat again with your torch making sure to heat the meta evenly . I usually darken the room a bit so I can see the solder flow around the edges better . Usually when your metal gets to the red hot phase your solder should have molten . Quench in water again and take a look that there are no gabs . If no gabs you can put your piece in the pickle solution for the clean up.

OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA

Your sterling silver will turn from black to a dull white when its ready to be taken out of the pickle . Take it out with copper tongues and only copper tongues or you might ruin your solution . Never quench a hot piece in your pickle or touch with your bare hands . Its an acid and as such dangerous.

OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA

Now you can add some texture with chasing tools or anything you have ( nails , screw drivers ect. ) Pre-polish with your flexshaft .You can put any finish on it that you like . I like a satin finish and thus use an 80 grit bristle brush , you can also use steel wool or sand paper and a bit of elbow grease. Add patina ( liver of sulfur ) and polish again until you like what you see. Punch or drill a hole for your jump ring and hang on a chain 🙂 Gift to somebody special or keep it yourself ( I kept mine )

OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA

Like what you see but are unable to make it yourself ? You can always visit my shop and have a look around 😉

www.nicilaskin.etsy.com