turtle doves

turtle dove ring set

ring set I made

I made this ring set out of sterling silver , my hubby is not sure if guys would like a ring in the shape of a bird , but I like them maybe you guys like them too the stone I used is a swiss blue topaz

out of this 🙂

out of this :)

I used 18 gauge sterling silver

drew the birds directly on the sheet

drew the birds directly on the sheet

cut them out with a jewelry saw

cut them out with a jewelry saw

the saw I use is a 6 inch saw ( distance between blade and the back part ) and 1/0 saw blades – my eyes are getting a bit weak so I have to feel now with my thumb to make sure the teeth are in the right direction

sawed out birds with extra length so that you can make a ring shank

sawed out birds with extra length so that you can make a ring shank

added texture

added texture

formed the rings so that the ends meet

formed the rings so that the ends meet

the fun part is soldering

the fun part is soldering

I love fire and my small welder ( its a hydroflux welder I got 2 years ago for my birthday – safer than a torch ) normally the flame is green but my flux solution is in need of replacing

soldered rings

soldered rings

the blackness comes from oxidation

after bathing the rings in a cleaning solution

after bathing the rings in a cleaning solution

the solution is called Pickle and will get rid of the blackness turning the metal white

now the rings are getting formed

now the rings are getting formed

ring mandrel and a nylon hammer will make sure you get a perfect round shape

I wanted to add a stone to the smaller ring

I wanted to add a stone to the smaller ring

I am lazy so I used a bought bezel cup to hold the stone and soldered that to the ring

almost finished they just need to be polished

almost finished they just need to be polished

I use a so called flex shaft ( dremel with a hose ) which is basically the same thing your dentist has for the drills

cleaned rings

cleaned rings

added some black max ( patina )

added some black max ( patina )

polished again

polished again

added the stone

added the stone

i saw that the ring with the stone did not have the patina for the eye so I had to do that

ring for her

ring for her

ring for him

ring for him

hope you liked it 🙂

hope you liked it :)

nici laskin

cuff links

skull cuff links – a small how to 🙂

www.nicilaskin.etsy.com

skull cuff links - a small how to :)

Cut out 2 discs

Cut out 2 discs
you want to make them at least 1 inch or the cuff links will be to small . I use a disc cutter but you can also cut them by hand with a jewelers saw

draw your skulls on a piece of paper and stick to your metal sheet

draw your skulls on a piece of paper and stick to your metal sheet
I used 20 gauge sterling silver for both the discs and the skulls ,I want to dome the cuff links later and when you go thicker they will dome funny

cut out your skulls and punch holes through eyes and nose for the saw blade

cut out your skulls and punch holes through eyes and nose for the saw blade
then feed your saw blade through the holes and saw out your eyes

make sure the skull fits well into the circle

make sure the skull fits well into the circle
I am lucky that I can eyeball very well ,I almost never measure ,but please do that before you end up with a too big of a skull for your circle

solder your skulls to the discs

solder your skulls to the discs
I use hard solder

now is the time to dome your discs

now is the time to dome your discs
The way to do is ,is to use a dabbing block ,its a steel block with half domed indentations and corresponding ball on sticks …

choose an indentation and put your disc in skull face down

choose an indentation and put your disc in skull face down

the ball hammer goes on top and the you hammer the end of it with a nylon hammer

the ball hammer goes on top and the you hammer the end of it with a nylon hammer
don’t use steel on steel as you will damage either your hammer or the ball on the stick 🙂 a raw hide hammer or nylon hammer is the best to use

domed skull circles

domed skull circles

now take your links and solder them to the back of your discs

now take your links and solder them to the back of your discs
I am lazy ,I buy the links ,its soooo much faster and they can make them better then I can

after soldering clean in your pickle solution until the metal turns white

after soldering clean in your pickle solution until the metal turns white

start polishing

start polishing
left is the polished one on the right is your non polished one

add patina ( liver of sulfur)

add patina ( liver of sulfur)
www.nic
now if you want to you can stop before adding patina and leave your cuff links like that ,nice and clean and in a ” raw” state ,or you can add patina and leave them all black or……….

…polish and leave the black in the nose and the eyes and a bit around the skulls

...polish and leave the black in the nose and the eyes and a bit around the skulls
that will give you a nice contrast

Today I made a pair of sterling silver skull cuff links…………

Today I made a pair of sterling silver skull cuff links............
hope you liked it

knuckle ring with butterfly

a6 a7 a8 a9 a10

 

Today another easy an fun project – a knuckle ring . Knuckle rings are to be worn – like the name suggests – above the knuckle . I have several that i wear daily , I prefer to have mine on my middle fingers on both hands . They are comfy and are adjustable so very easy to make .

Knuckle rings are the same size usually as toe rings or pinky rings an have an open back ( to adjust them easy )

a a1 a2 a3 a4 a5 a6

 

cut a 45-47 mm long piece from sterling silver flat wire ( i use 3mm by 1 mm thick wire that i get from http://www.riogrande.com . The wire is perfect for toe rings and small ring shanks and I use a lot of it . Cut your butterfly out with a jewelry saw and 1/0 blades from your metal sheet ( i used 20 gauge here ) . File the edges of your wire strip and of the butterfly so that everything is smooth and wearable . Form your wire on a ring mandrel ( size 3 is usually a good size ) . I used a dapping block to dome the butterfly to make it more organic looking but if you prefer you can keep it flat .

Solder your butterfly to the ring shank . Quench in water and then clean in pickle solution . After your ring is clean take your flex shaft and polish your ring . Done . Now you can wear your little knuckle ring proudly on any finger ( remember because we did not solder the ends together the ring is totally adjustable .

 

www.nicilaskin.etsy.com   if you are interested