turtle doves

turtle dove ring set

ring set I made

I made this ring set out of sterling silver , my hubby is not sure if guys would like a ring in the shape of a bird , but I like them maybe you guys like them too the stone I used is a swiss blue topaz

out of this 🙂

out of this :)

I used 18 gauge sterling silver

drew the birds directly on the sheet

drew the birds directly on the sheet

cut them out with a jewelry saw

cut them out with a jewelry saw

the saw I use is a 6 inch saw ( distance between blade and the back part ) and 1/0 saw blades – my eyes are getting a bit weak so I have to feel now with my thumb to make sure the teeth are in the right direction

sawed out birds with extra length so that you can make a ring shank

sawed out birds with extra length so that you can make a ring shank

added texture

added texture

formed the rings so that the ends meet

formed the rings so that the ends meet

the fun part is soldering

the fun part is soldering

I love fire and my small welder ( its a hydroflux welder I got 2 years ago for my birthday – safer than a torch ) normally the flame is green but my flux solution is in need of replacing

soldered rings

soldered rings

the blackness comes from oxidation

after bathing the rings in a cleaning solution

after bathing the rings in a cleaning solution

the solution is called Pickle and will get rid of the blackness turning the metal white

now the rings are getting formed

now the rings are getting formed

ring mandrel and a nylon hammer will make sure you get a perfect round shape

I wanted to add a stone to the smaller ring

I wanted to add a stone to the smaller ring

I am lazy so I used a bought bezel cup to hold the stone and soldered that to the ring

almost finished they just need to be polished

almost finished they just need to be polished

I use a so called flex shaft ( dremel with a hose ) which is basically the same thing your dentist has for the drills

cleaned rings

cleaned rings

added some black max ( patina )

added some black max ( patina )

polished again

polished again

added the stone

added the stone

i saw that the ring with the stone did not have the patina for the eye so I had to do that

ring for her

ring for her

ring for him

ring for him

hope you liked it 🙂

hope you liked it :)

nici laskin

flower ring with blue topaz

flower ring ring3 ring ring5 ring2

I love flowers , all kind of flowers and I was thinking a ring would go nicely with that butterfly garden bracelet

Again its made from sterling silver sheet and a piece of 5mm x 1.25 mm sterling silver wire cut to length to make the ring shank. I like using flat wire stock and 1.25 mm is a nice thickness for making rings . This time i took some pictures of the process so you can see how much work is involved in it . However since I have been doing this for a while a ring like that only takes me about 1 hour .

I cut the flower out of 20 gauge sterling silver sheet and measured the wire out to 53 mm which gives me a ring size of 5 1/2 when done ( my right ring finger is a 5 1/2 my left is a 4 1/2 , yes my fingers are tiny ) the wire was bend with my pliers so that the ends meet flush and then soldered with silver solder ” easy” , You have to clean the shank before soldering the flower to it and form it so i put it into a pickle bath ( please wear gloves that stuff is very bad on your skin ) after the bath you form the ring on a ring mandrel with a nylon hammer so as to leave no marks . I chased some lines into my flower with some chasing tools , then used the dabbing block again to shape a dome , my trusted pliers took care of the rest ( bending the pedal ends down wards – use a soft pliers for the bending or it will mark the metal ) for the middle of the flower I decided to set a stone and because I am inherently LAZY i used a so called bezel cup that you can buy at any jewelry supply store > I could have made my own but again i am lazy and I wanted to be fast :)

The flower was soldered onto the ring and the cup soldered onto the the flower using ” extra easy ” wire solder . Quench in cold water and put into the pickle solution again

My husband always laughs when i say pickle solution . I am German , born and raised in Leipzig , East Germany and pickle in German means pimple . He finds that funny…………….and we will leave it at that :)

after you get the oxidation off with the pickle you need to polish the ring before setting the stone , I am using a blue Topaz from Switzerland, Polishing something that small is best done with the flex shaft so that you get in every corner . Apply patina , polish again and set the stone , carefully pushing the teeth of the cup over the stone . Polish by hand with a polishing cloth and voila

 

A ring :)

 

process of making the flower ring a2 a3 a4 a5 a7 a8 a9 a10 a11 a12 a13 a14 a15 a16 a17 a18